Judo JRSF Series Installation And Operating Instructions Manual Download Page 53

Page: 53 / 55

Installation and operating instructions: JUDO JRSF automatic backwashing protection filter JRSF-ATP DN 125 - 200 (time and differential pressure controlled)

JUDO Wasseraufbereitung GmbH

Postfach 380



D-71351 Winnenden

Translation into foreign languages and reproduction, even in excerpt form, is only permitted with special
approval.

Tel. +49 (0)7195-692-0



Fax +49 (0)7195-692-188

Revision level: 24.05.2017

E-mail: [email protected]



judo.eu

7.4.1

Spare parts

Model JRSF-ATP

DN125

DN150

DN200

Item

Designation

Pcs

Order no. Order no. Order no.

2 - 4 Replacement part set filter */**

2300099

2300101

2300103

4, 15-21 Replacement part complete DN125

2635128

–

Replacement part complete DN150

–

2636128

–

Replacement part complete DN200

–

2637128

6 O-ring 60x5

1635107

16 Rubber semi-ellipse

2635126

22 O-ring 20x2

1635115

23 Permatight seal

1635117

34 Linear drive

1510165

43 Control unit JSK V

1510162

44 Shut-off valve DN50 EW

1980499

–

Shut-off valve DN65 EW

–

1980500

–

Shut-off valve DN80 EW

–

1980501

JEM 3/2 way solenoid valve G ¼“

1510022

Exhaust throttle G ¼“

1980502

59 Hose 6x4 mm

1100018

60.1 Differential pressure gauge 0 - 2.5 bar

1610011

**** Main switch

1500509

**** Circuit board with transformer

1510173

**** Primary fuse (F1)

1510149

**** Secondary fuse (F2)

1500382

Tab. 14: Spare parts (item numbers related to Table 13 Parts List)

Wear part

Custom mesh size available upon request

***

When ordering, please specify the length required in metres

****

Not shown

If a new control unit is required as a spare part, the rated diameter of the relevant JUDO

JRSF automatic backwashing protection filter must be specified with the control unit

order so that the new control unit can be loaded with the filter-specified software in the

factory.

7.5

Transfer confirmation and maintenance log

The attached transfer confirmation must be carefully filled out upon commissioning!

The attached maintenance log must be carefully filled out during maintenance work and

serves as a template for the creation and orderly keeping of an on-going maintenance

book!

Summary of Contents for JRSF Series
























































Search results

Summary of Contents for JRSF Series

Reviews:

Related manuals for JRSF Series

Brands by name

Popular brands

Judo JRSF Series, Installation And Operating Instructions Manual

Search results

Summary of Contents for JRSF Series

Reviews:

Related manuals for JRSF Series

Brands by name

Popular brands