Judo JRSF Series Installation And Operating Instructions Manual Download Page 6

Page: 6 / 55

Installation and operating instructions: JUDO JRSF automatic backwashing protection filter JRSF-ATP DN 125 - 200 (time and differential pressure controlled)

JUDO Wasseraufbereitung GmbH

Postfach 380



D-71351 Winnenden

Translation into foreign languages and reproduction, even in excerpt form, is only permitted with special
approval.

Tel. +49 (0)7195-692-0



Fax +49 (0)7195-692-188

Revision level: 24.05.2017

E-mail: [email protected]



judo.eu

Introduction

1.1

About these installation and operating instructions

These installation and operating instructions should simplify getting to know your JUDO JRSF automatic

backwashing protection filter and inform you of its intended applications. The installation and operating

instructions contain important information so that you can use the JUDO JRSF automatic backwashing

protection filter, safely, professionally and economically. They contain basic information that must be

observed during installation, operation and maintenance. Observance of this information will help to avoid

dangers, reduce repair costs and increase the reliability and service life of your JUDO JRSF automatic

backwashing protection filter.

Alongside the installation operating instructions and the legal regulations applicable in the country and place

of use in respect of accident prevention, the recognised technical regulations for safe and professional work

must be observed.

All pictorial, dimensional and implementation information correspond to the date of going to press. We

reserve the right to make changes due to technical progress and continuing development. Model and

product claims cannot be lodged.

The installation and operating instructions must always be available at the place of use

of the JUDO JRSF automatic backwashing protection filter and must be kept in a good,

legible state!

All persons involved in installation, commissioning, operation, maintenance, servicing

and repair of the JUDO JRSF automatic backwashing protection filter must be

appropriately qualified and trained and must have carefully read and understood these

installation and operating instructions and also any separate installation and operating

instructions for other devices and systems!

1.2

Validity of these installation and operating instructions

These installation and operating instructions are valid for the following models:

Designation

Model

Order no.

JUDO JRSF automatic backwashing protection filter

JRSF-ATP DN 125

8503035

JUDO JRSF automatic backwashing protection filter

JRSF-ATP DN 150

8503036

JUDO JRSF automatic backwashing protection filter

JRSF-ATP DN 200

8503037

Tab. 1: Models

Summary of Contents for JRSF Series
























































Search results

Summary of Contents for JRSF Series

Reviews:

Judo JRSF Series, Installation And Operating Instructions Manual, Page: 6 / 55

Search results

Summary of Contents for JRSF Series

Reviews: