Judo JRSF Series Installation And Operating Instructions Manual Download Page 9 | Manualshive

Page: 9 / 55

Judo JRSF Series Installation And Operating Instructions Manual Download Page 9

Installation and operating instructions: JUDO JRSF automatic backwashing protection filter JRSF-ATP DN 125 - 200 (time and differential pressure controlled)

All rights reserved.

JUDO Wasseraufbereitung GmbH

© JUDO Wasseraufbereitung GmbH

Postfach 380



D-71351 Winnenden

Translation into foreign languages and reproduction, even in excerpt form, is only permitted with special
approval.

Tel. +49 (0)7195-692-0



Fax +49 (0)7195-692-188

Revision level: 24.05.2017

E-mail: [email protected]



judo.eu

9

2.4

General safety instructions

Warning

Any working methods that might endanger safety must be avoided!

Non-observation of these installation and operating instructions and the safety

instructions herein may endanger persons as well as the environment and the JUDO

JRSF automatic backwashing protection filter itself!

The safety instructions do not take into account



Random happenings and events that may occur during installation, operating and maintenance.



Location related safety conditions for the observance of which the operator is responsible, even for
contract installation personnel.

Attention

Unauthorised conversions and changes to the JUDO JRSF automatic backwashing

protection filter or tampering with system components are forbidden for safety reasons!

Do not perform any changes, make any additions or carry out any conversions that
could impair safety without the manufacturer’s written approval!
Never remove safety equipment or deactivate it by making changes to the JUDO JRSF

automatic backwashing protection filter!

The safety instructions of these installation and operating instructions must be

observed without fail, additional industry-wide and in-house safety instructions remain

in force!

Only operate the JUDO JRSF automatic backwashing protection filter with the caps and

covers of all system components correctly closed!

Fault-free operation of the JUDO JRSF automatic backwashing protection filter is only

ensured if original spare parts and components are used in the combination described

in these installation and operating instructions, otherwise there is a risk of

malfunctioning or damage!

Only allow authorised technical personnel to carry out repairs!

All work on electrical system components must only be performed by qualified

electricians certified according to an approved national scheme!

The electrical system components must be checked regularly!

Loose connections must be tightened immediately and damaged system components

immediately replaced!

«
...
7
8
9
10
11
...
»

Summary of Contents for JRSF Series
























































Reviews:

No comments