manualshive.com logo in svg

Judo JRSF Series, Installation And Operating Instructions Manual, Page: 46 / 55

Share
Download
Judo JRSF Series Installation And Operating Instructions Manual Download Page 46

 

 

 

 

Installation and operating instructions: JUDO JRSF automatic backwashing protection filter JRSF-ATP DN 125 - 200 (time and differential pressure controlled)                                                                                                                                                                           

 

All rights reserved. 

JUDO Wasseraufbereitung GmbH 

© JUDO Wasseraufbereitung GmbH 

Postfach 380 

 D-71351 Winnenden 

Translation into foreign languages and reproduction, even in excerpt form, is only permitted with special 
approval. 

Tel. +49 (0)7195-692-0 

 Fax +49 (0)7195-692-188 

Revision level: 24.05.2017 

E-mail: [email protected] 

 judo.eu 

46  

 

 

 

The JUDO JRSF automatic backwashing protection filter should where possible be in the 

operating position!

 

7.1.1 

Replacing the control unit 

 

  Switch off the power supply and secure to prevent switching back on (pull out the mains plug). 

  Disconnect the linear drive from the control unit at the coupling, disconnect the electrical connecting 

cables and the replace the control unit. 

  Reconnect the electrical connecting cables, leave the linear drive disconnected. 

  Remove the cover plate at the motor mounting, release and remove the linear drive from the lever 

and then the motor mounting to avoid possible damage to the linear drive or JUDO JRSF automatic 

backwashing protection filter. 

  Connect the linear drive to the control unit, then switch on the control unit.  

  Trigger manual backwashing by pressing the key 

 (5 seconds). In doing so the Hall pulses for 

positioning the linear drive are balanced with the new control unit. 

 

 

If the control unit indicates “Hall fault”, proceed according to Chap. 7.1.3! 

 

  Switch off the control unit and disconnect the linear drive from the control unit. 

  Reinstall the linear drive correctly in the motor mounting. 

  Reconnect the linear drive with the control unit, switch on and program according to the local 

requirements (see Chap. 5.4 - 5.5). 

7.1.2 

Replacing the linear drive 

 

  Switch off the power supply and secure to prevent switching back on (pull out the mains plug). 

  Disconnect the linear drive from the control unit at the coupling. 

  Remove the cover plate at the motor mounting, release and remove the linear drive from the lever 

and then the motor mounting. 

  Connect the new linear drive to the control unit, then switch on the control unit.  

  Trigger manual backwashing by pressing the key 

 (5 seconds). In doing so the Hall pulses for 

positioning the new linear drive are balanced with the control unit. 

 

 

If the control unit indicates “Hall fault”, proceed according to Chap. 7.1.3! 

 

  Switch off the control unit and disconnect the linear drive from the control unit. 

  Reinstall the new linear drive correctly in the motor mounting. 

  Reconnect the linear drive with the control unit, switch on and, if necessary, reprogram according to 

the local requirements (see Chap. 5.4 - 5.5). 

Summary of Contents for JRSF Series
























































Reviews:

No comments