Judo JRSF Series Installation And Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 55

background image

Installation and operating instructions: JUDO JRSF automatic backwashing protection filter JRSF-ATP DN 125 - 200 (time and differential pressure controlled)

All rights reserved.

JUDO Wasseraufbereitung GmbH

© JUDO Wasseraufbereitung GmbH

Postfach 380



D-71351 Winnenden

Translation into foreign languages and reproduction, even in excerpt form, is only permitted with special
approval.

Tel. +49 (0)7195-692-0



Fax +49 (0)7195-692-188

Revision level: 24.05.2017

E-mail: [email protected]



judo.eu

15

3.5

Technical data

Performance data

JRSF-ATP

DN125

DN150

DN200

Rated flow *

(with 0.2 bar pressure loss)

[m³/h]

75

110

170

Required backwashing water flow

[l/s]

10

15

24

Mechanical, hydraulic, pneumatic data

Flange connection input/output

DN 125 DN 150 DN 200

Flange connection flushing water

DN 50

DN 65

DN 80

Connection, solenoid valve

["]

¼ female thread

Maximum permissible operating pressure

[bar]

10

Min. required flow pressure

[bar]

1.5

Necessary control pressure

[bar]

6.0 - 8.0

Maximum permissible differential pressure

[bar]

0.5

Pressure loss after backwashing *

[bar]

0.2

Max. compressive / tensile force linear drive

[N]

6000 / 4000

Maximum permissible temperature of medium

[°C]

75

Mesh size permanent filter insert

[mm]

0.1

Required site-provided control medium

Control air

(dry + filtered)

Electrical data

Power supply (via mains plug)

[VAC]

230

Frequency

[Hz]

50

Max. control unit power consumption

[W]

60

Max. loading potential-free relay contact

[V/A]

24/1

Internal device fuse primary / secondary

[A]

0.63 slow / 2.5 slow

Electrical connection linear drive

[VDC/A]

24/5

Power consumption, solenoid valve

[W]

8

Control unit, degree of protection (closed housing cover)

IP 54

Solenoid valve degree of protection (fitted device plug)

IP 65

Weight

Net weight backwashing protection filter

[kg]

62

92

122

Shut-off valve with pneumatic drive

[kg]

6.5

8

8.5

Control unit

[kg]

3.5

General data

Sealing material, solenoid valve

NBR

Blocking seal, shut-off valve

EPDM

Tab. 4: Technical data

* Related to drinking water with a clean filter (technical advice is required for process
water or heavily contaminated water)!
** Different with custom mesh size!

«
...
13
14
15
16
17
...
»

Summary of Contents for JRSF Series
























































Reviews:

No comments

Related manuals for JRSF Series

Brand: ORMA Pages: 5

EASYpure II UV 1302 Series

Brand: Barnstead Pages: 40

Brand: Hunter Pages: 2

Brand: ubbink Pages: 55

ProVent 400 Series

Brand: MANN+HUMMEL Pages: 5

Brand: Geekpure Pages: 23

Brand: brondell Pages: 56

Brand: A.O. Smith Pages: 20

Brand: Baccara Pages: 23

Brand: Whirlpool Pages: 5

Brand: Whirlpool Pages: 24

Brand: Hydac Pages: 56

Domestic R.O. System RO300

Brand: BWT Pages: 6

Brand: MiniMax Pages: 3

Brand: Komet Pages: 65

Brand: Zephyr Pages: 6

Brand: Atlas Filtri Pages: 20

Brand: Graf Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands