manualshive.com logo in svg

JPS Communications NXU-2, Installation And Operation Manual

Share
Download
JPS Communications NXU-2 Installation And Operation Manual Download Page 7

NXU-2 Operations Manual 

 

 

1-1 

JPS Communications, Inc.

 

1  General Information 

1.1  Scope 

This instruction manual provides the information necessary to install and operate the NXU-2 
Network Extension Unit. 

1.2  Description 

1.2.1  NXU General 

NXU stands for 

N

etwork E

x

tension 

U

nit.  NXU units connect communications equipment to a 

digital network using VoIP (Voice over Internet Protocol) technology.  NXU units use JPS’ 
proprietary technology, embodied in a family of hardware and software products that enable 
voice communications devices to be interconnected via a network across the room or around 
the world.  Voice over Internet Protocol, known as VoIP, is a means of digitizing voice signals 
and transmitting them over a digital network, such as a LAN, WAN or even the Internet itself. 

1.2.1.1  Advantages of NXU Technology 

??

Enables the design of low cost, extremely flexible radio communications networks. 

??

Multiplexes voice audio and data over a standard Ethernet network. 

??

Uses existing network infrastructure eliminating the need for leased lines and 
microwave sites. 

??

Eliminates the requirement for pilot tones and other in-band signaling. 

??

Facilitates centralized control of a communications network from a single computer. 

1.2.2  NXU-2 Description 

The NXU-2 is intended for use with radio communications consoles, communications radios, 
and JPS products such as the ACU-1000 Interconnect Unit.  A general-purpose stand-alone 
device interfaces full duplex audio, one RS-232 port, and three status bits onto an Ethernet 
network. A pair of NXU-2s can form a simple system that creates a transparent 
communications link between the two. The NXU-2 at one end (usually the equipment end) is 
the 

server

; the one at the other end (usually the operator end) is the 

client

.  The audio, RS-232, 

and status bits are transparently transferred between the server and the client.   

Any NXU-2 can be set up as a server or as a client depending on system needs. The RS-232 
interface allows for different baud rates between the server and the client. 

The NXU-2 monitors its network connection and adjusts its parameters automatically to 
provide optimum performance under varying network conditions.  Front panel indicators 
display the unit’s status.  Initial configuration is done through the NXU-2’s  serial port, but 

Summary of Contents for NXU-2






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands