JPS Communications NXU-2 Installation And Operation Manual Download Page 10

Page: 10 / 53

NXU-2 Operations Manual

1-4

JPS Communications, Inc.

1.5 Specifications

Table 1-1

Specifications

RX Audio Input

Input impedance

Balanced 47k ohms, transformer coupled.

Input Level

Incoming signals adjustable from –30 to +11 dBm to set 0 dBm nominal input;
+15 dBm clipping.

Frequency Response

10 Hz to 3600 Hz +/- 2dB.

TX Audio Output

Output Impedance

Unbalanced 10 ohms, AC Coupled.

Output Level

Adjustable from –30 to +11 dBm, 0 dBm nominal factory default; +15 dBm
clipping into a 600 ohm load.

Frequency Response

10 Hz to 3350 Hz +/- 2dBm.

Distortion

0.5% or less (excepting Vocoder).

COR & AUX Input

Input impedance

47k ohm pull-up to +5V.

Polarity

COR: Selectable active low or active high; AUX Inputs: Active low.

Threshold

+2.5V nominal.

Protection

Up To + 100 VDC.

PTT and AUX Output

Output Type

Open drain, 47k ohm pull-up to +5V.

Maximum Sink Current

100 mA.

Max Open Circuit Voltage

+60 VDC.

Serial Interface

Interface Type

RS-232, Asynchronous, Full Duplex.

Baud Rates

300, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 bps.

Connector

DB-9 Male, Standard PC/AT DCE Pinout.

Network Interface

Interface Type

10BASE-T Ethernet, 10Mbps; RJ-45 Connector.

Protocols

Audio and status-UDP, RS-232- TCP.

Audio Vocoder

Selectable, 13, 16, 24, 32, or 64 Kbps data rate.

General/Environmental

Programming/Configuration

Web, Telnet, or RS-232 Interface.

Front Panel

Power, Link Active, Channel Active, and Audio Level LEDs.

Rear Panel

Audio/Data, Serial, Network, and Power Connectors.

Audio/Data Connector

DB-15 Female.

Input Power (12 VDC Nom)

+11 to +15 VDC @ 0.5A max. 12VDC (Wall-cube supplied).

Power Connector

Coaxial Jack, 2.5 mm ID, 5 to 5.5 mm OD; Center Pin Positive; Reverse
Polarity Protected.

Size and Weight

1.7” H x 7”W x 9”D (4.3 x 17.8 x 22.9 cm). 4lbs. (1.8kg).

Temperature

Operating: -20 to +60 degrees C. Storage: -40 to +85 degrees C.

Humidity

Up to 95% @ 55 degrees C.

Shock

MIL-STD-810D, Method 516.3, Procedure VI.

Vibration

MIL-STD-810D, Method 514.3, Category 1.

Summary of Contents for NXU-2






















































Search results

Summary of Contents for NXU-2

Reviews:

Brands by name

Popular brands

JPS Communications NXU-2, Installation And Operation Manual

Search results

Summary of Contents for NXU-2

Reviews:

Brands by name

Popular brands