manualshive.com logo in svg

JPS Communications NXU-2, Installation And Operation Manual

Share
Download
JPS Communications NXU-2 Installation And Operation Manual Download Page 19

NXU-2 Operations Manual 

 

 

2-7

 

JPS Communications, Inc.

 

2.6  Power Requirements 

The NXU-2 is designed to operate from a n12V DC supply.  The unit will meet all of 
its specifications over a voltage range of +11 to +15 VDC.  The DC power consumption is 500 
mA maximum.  The AC adapter provided with the unit meets these specifications. To power 
the unit from a12V DC source, a 2.1mm I.D. coaxial power plug will be required to 
connect the power source to J6 on the NXU-2 rear panel. The center conductor is positive (+). 

NOTE:

 

Do not exceed 15VDC input to the NXU-2. The NXU-2 contains a 

15V zener diode across the DC input to protect internal circuits from 

transient

 

overvoltage. Attempting to power the NXU-2 from a 

constant

 DC source that 

delivers more than 15V may damage the zener diode and/or other components 
and render the unit inoperative 

The NXU-2 is a microprocessor-controlled device.  As with any such equipment, a very short 
loss of power can cause operational problems and/or cause the unit to reset.  The 
communications link will be inoperable during the reset period.  JPS recommends the NXU-2 
and associated equipment be connected to an AC power source that utilizes an uninterruptible 
power system (UPS).  If the overall site does not have UPS capability, the NXU-2 should be 
plugged into a smaller UPS, such as those used for personal computer systems 

2.7  Installation Checklist 

Table 2-1 

Basic Installation Checklist 

Determine NXU-2 network parameters 
such as IP address, subnet mask, and 
gateway address. 

You must assign these values. If you are not sure 
how to determine these values, see the network 
administrator for your organization. 

Provide suitable power for the device. 

See section 2.6 Power Requirements. 

Make interconnections. 

See Section 2.8.2  Audio Level Adjustment 
Potentiometers and Input Test Point for External 
Interconnect Information. 

Configure NXU-2 parameters. 

See Section 3 Configuration. 

Adjust audio levels. 

See Section 4.4.2 Front Panel Indicators. 

2.8  Rear Panel Adjustments and Connectors 

Refer to Figure 2-2 

Control and Connector Locations for a view of the NXU-2 Rear Panel.  

All rear panel connectors and adjustment potentiometers are explained in the section below, 
starting at the left side of the panel. 

2.8.1  DC Input Connector, J6 

The NXU-2 operates on a n12 VDC.  The power is applied through J6 via the “Wall 
Cube” AC adapter provided with the unit, or through a 2.1mm I.D. coaxial plug. 

Summary of Contents for NXU-2






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands