manualshive.com logo in svg

JPS Communications NXU-2, Installation And Operation Manual

Share
Download
JPS Communications NXU-2 Installation And Operation Manual Download Page 14

NXU-2 Operations Manual 

 

 

2-2

 

JPS Communications, Inc. 

Plainly, mark with indelible ink all mailing documents as follows: 

 

  GOODS RETURNED FOR REPAIR 

Mark all sides of the package:  

 

FRAGILE - ELECTRONIC EQUIPMENT 

Inspect the package prior to shipment to be sure it is properly marked and securely wrapped. 

2.4  Installation Overview  

NOTE:

 

NXU-2 installation requires knowledge of Ethernet network 

fundamentals as well as a basic understanding of Internet Protocol (IP.) As with 
any network-connected device, improperly configuring and installing the NXU-2 
could disrupt proper network operation. Please seek the assistance of your 
network administrator or other knowledgeable person if you are unsure about 
how your network is configured. 

Six steps are needed to properly install the NXU-2.  These steps are: 

1.  Determine the IP address, subnet mask, and (if applicable) the gateway address for 

the unit. You may have to contact the network administrator for your organization to 
obtain this information.  

Note:

 

Operation of the NXU-2 is not possible without this information. 

2.  Provide the proper primary power for the unit. In most cases, this requirement will 

be met by the AC adapter that is included with the NXU-2. 

3.  Interconnect the unit with the communications system via the NXU-2's rear panel 

connectors. J7 provides the audio and control lines necessary to interface the NXU-
2 to your audio equipment. 

4.  Configure the unit’s operational parameters per Sections  3.2  Serial Port 

Configuration through 3.4 Network Configuration.  

5.  Connect the unit to your Ethernet network using the supplied Ethernet cable per 

Section 2.8.4 Network Connection, J3 

6.  Set the input and output audio levels per Section  4.4.2  Input/Output Level 

Adjustments. 

The NXU-2 is then ready to use. 

Summary of Contents for NXU-2






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands