manualshive.com logo in svg

JPS Communications NXU-2, Installation And Operation Manual

Share
Download
JPS Communications NXU-2 Installation And Operation Manual Download Page 39

NXU-2 Operations Manual 

 

 

4-3

 

JPS Communications, Inc.

 

4.4.5  Auxiliary I/O 

The NXU-2 has two sets of independent inputs and outputs, which may be used for control of 
the user’s equipment. AUX IN 0 and AUX IN 1 are active-low inputs which, when activated on 
one end, will cause AUX OUT 0 and AUX OUT 1 on the other end to become active. The 
AUX OUT lines are open drain devices and each is capable of sinking 100 mA. 

Note: the 

auxiliary I/O lines are designed for switching and control applications, and do not have quick 
enough response times to send or receive data.

 

4.5  Controlling Connections 

Normally the NXU-2 client automatically connects to the preprogrammed NXU-2 server when 
power is applied. The user may also manually control the connection state of the NXU-2 client. 
This can be done via the serial port (by entering command mode as described in Section  3.3.1 
Entering the Configuration Mode) or via the network using Telnet or a Web Browser. 

4.5.1  Serial or Telnet Control 

When using the serial port (in command mode) or Telnet, the user may disconnect a client from 
a server by typing: 

DISC 

 A connection may be made to a server by typing: 

CONN

 <IP address> 

The status of these commands may be viewed by typing: 

STAT 

STAT returns the following responses: 

CON

 <IP address> 

The unit is connected to an NXU-2 at address <IP address> 

DIS

 

 

 

The unit is not connected 

ATT

 <IP address> 

The unit is attempting a connection to <IP address> 

Depending upon the characteristics of the network, the CONN and DISC commands may not 
take effect immediately. In order to determine when a CONN or DISC command has 
completed, issue the STAT command repeatedly to poll the status of the connection. 

Summary of Contents for NXU-2






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands