manualshive.com logo in svg

JPS Communications NXU-2, Installation And Operation Manual

Share
Download
JPS Communications NXU-2 Installation And Operation Manual Download Page 35

NXU-2 Operations Manual 

 

 

3-13

 

JPS Communications, Inc.

 

 

Figure 3-8 

Network Configuration Screen 

3.5  I/O DESCRIPTIONS 

This  section provides detailed explanations of the NXU-2’s audio interfaces and its parallel 
control inputs and outputs. 

3.5.1  Audio Input 

The NXU-2 audio input is 47K ohm, balanced. It can be used as an unbalanced input by 
grounding one half of the balanced pair and connecting the single-ended input to the remaining 
half. The use of balanced inputs and shielded cables is recommended for superior immunity to 
noise. 

The audio input will accept signal levels from  –30 to +11 dBm.  Internal circuitry is used to 
amplify or attenuate this input as necessary to optimize the level to the DSP.  The signal level is 
adjusted by the IN LVL potentiometer accessible from the rear panel.  The input is set to 0 
dBm when shipped.  This means the IN LVL potentiometer is adjusted so that an audio input of 
0 dBm provides the correct level to the DSP circuitry. 

Summary of Contents for NXU-2






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands