manualshive.com logo in svg

JPS Communications NXU-2, Installation And Operation Manual

Share
Download
JPS Communications NXU-2 Installation And Operation Manual Download Page 24

NXU-2 Operations Manual 

 

 

3-2

 

JPS Communications, Inc. 

3.3.1  Entering the Configuration Mode  

With the serial cable connected and the PC running a terminal program set to the above 
parameters, apply power to the NXU-2. (

HyperTerminal

 is a suitable terminal program, which 

is included with most Windows

T M

-based PC systems. See Section 3.3.1.1) 

3.3.1.1  Hyper Terminal Setup and Use 

Hyper Terminal must first be setup to run off the computer serial port. The following setup 
information should allow Hyper Terminal to be set to communicate with the NXU-2 via the 
RS-232 serial port. Hyper Terminal comes with Windows, it is located on the Windows Start 
Bar, click PROGRAMS, click ACCESSORIES, click COMMUNICATIONS, click HYPER 
TERMINAL, the Hyper Terminal Window appears, then double click the HYPERTRM.EXE 
icon. See Figure 3-1 

Windows Path to Hyper Terminal and Figure 3-2 

Hypertrm.EXE 

Screen. 

 

Figure 3-1 

Windows Path to Hyper Terminal 

Summary of Contents for NXU-2






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands