manualshive.com logo in svg

JPS Communications NXU-2, Installation And Operation Manual

Share
Download
JPS Communications NXU-2 Installation And Operation Manual Download Page 31

NXU-2 Operations Manual 

 

 

3-9

 

JPS Communications, Inc.

 

STAT - Return this client's current connection status 

STOP <1/2> - Set the serial port stop bits 

SUBNET <ip address> - Set IP subnet mask for this unit 

TRAN - Place this unit's serial port in transparent mode 

VER - Print the software version information for this unit 

VOCODER <number> - Select the voice compression method (1-5) 

WHAT - Print a description of this unit's settings 

3.3.3  Setting Unit IP Address 

The first thing you should do is to set the IP address of the unit. The NXU-2 comes from the 
factory with a default IP address set to 192.168.1.200. Set the address by typing: 

MYIP <IP address> 

Where <IP  address> is the IP address of the unit in dotted quad notation. All configuration 
commands are entered by a carriage return. In this example, if your desired IP address is 
192.168.1.1 you would type MYIP 192.168.1.1 and press ENTER 

3.3.4  Setting Unit Subnet Mask and Gateway Address 

Now set your subnet mask using the SUBNET command. If you are using a gateway, set the 
gateway address (the address of your router) using the GATEIP command. If on a LAN with no 
gateway, leave the gateway address set at the default address 0.0.0.0. 

3.3.5  Using DHCP to Assign IP Parameters  

If you have a DHCP server on your network, you may configure the NXU-2 to obtain its IP 
address, subnet mask, and gateway address via DHCP. Setting the NXU-2 IP address to 0.0.0.0 
will cause it to attempt to contact a DHCP server on power-up. NOTE: Using DHCP is not 
recommended for NXU-2 Server units since the IP address assigned by the DHCP server is not 
generally known and is subject to change. If DHCP is to be used, it should only be used on 
client NXU-2 units. 

3.3.6  Setting VoIP Port (Optional) 

The default port used by the NXU-2 for the transport of audio across the network is 1221. 
Under normal circumstances, this should not be changed. The default port may be changed, if 
necessary, by using the PORT command. Type PORT <port number> and press ENTER to 
select a new default port. The port number must range from 1 to 65535. 

3.3.7  Client/Server Selection 

Whether the unit will be a client (a unit which can make and break connections) or a server (a 
unit which only accepts connections from a client) will need to be decided. This selection is 
made with the CONMODE command. CONMODE 0 configures the unit as a client, while 
CONMODE 1 configures the unit as a server. For a client unit, you also need to set the IP 

Summary of Contents for NXU-2






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands