manualshive.com logo in svg

JPS Communications NXU-2, Installation And Operation Manual

Share
Download
JPS Communications NXU-2 Installation And Operation Manual Download Page 13

NXU-2 Operations Manual 

 

 

 

JPS Communications, Inc.

 

2-1 

2  Installation 

2.1  General 

This section provides the instructions for unpacking, inspection, installation and set-up.  Also 
included are directions for reshipment of damaged parts or equipment. 

2.2  Unpacking and Inspection 

After unpacking the unit, retain the carton and packing materials until the contents have been 
inspected and checked against the packing list.  If there is a shortage or any evidence of 
damage, do not attempt to use the equipment.  Contact the carrier and file a shipment damage 
claim.  A full report of the damage should also be reported to the JPS Customer Service 
Department.  The following information should be included in the report: 

??

Order Number 

??

Equipment Model and Serial Numbers 

??

Shipping Agency 

??

Date(s) of Shipment 

??

The JPS Customer Service Department can be reached by phone at (919) 790-1011, by 
fax at (919) 790-1456.  Upon receipt of this information, JPS will arrange for repair or 
replacement of the equipment. 

2.3  Reshipment of Equipment 

If it is necessary to return the equipment to the manufacturer, a Returned Material 
Authorization (RMA) number must first be obtained from JPS.  This number must be noted on 
the outside of the packing carton and on all accompanying documents. When packing the unit 
for reshipment, it is best to use the original packaging for the unit; if this is not possible, make 
sure that adequate packing material is used to prevent excessive shocks during transport and 
handling. 

Shipment should be made prepaid consigned to: 

 

JPS Communications, Inc. 

 

Customer Service Departme nt 

 

5800 Departure Drive 

 

Raleigh, North Carolina 27616 

 

USA 

Summary of Contents for NXU-2






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands