JOSAM AM10 Manual Download Page 48

Page: 48 / 56

JOSAM laser AM
Measuring system

Measurement of caster
Use the wheel alignment gauge AM300/301 and
turn angle gauge AM135.

Left side
(1) Attach wheel alignment gauge AM300/301 on

the spindle of the wheel adapter through the
hole for camber and caster measurement.

Move the wheel alignment gauge toward the
locking pin.

(2) Turn the left wheel 20

outward utilizing

the turn angle gauge.

(3) Place the wheel alignment gauge vertically

using the top bubble and lock with the
bottom knob.

(4) Rotate the measuring scale so that the

measuring bubble shows a horizontal position.

(5) Place the moveable pointer on 0 at the

inner measuring scale.

(6) Rotate the left front wheel 20

inward utilizing

the turn angle gauge.

Measurement of front axles

Left 20

inwards

Left 20

outwards

Place the wheel alignment gauge level using the top
bubble and lock with the lower knob.

(7) Turn the measuring scale so that the

measuring bubble shows a horizontal position.

(8) Read the caster value at the pointer on the

inner measuring scale in degrees

and

minutes ´.

Write down the value on the Test Report Sheet.

Summary of Contents for AM10

























































Search results

Summary of Contents for AM10

Reviews:

Related manuals for AM10

Brands by name

Popular brands

JOSAM AM10, Manual

Search results

Summary of Contents for AM10

Reviews:

Related manuals for AM10

Brands by name

Popular brands