5538117-UIM-B-0319
6
Johnson Controls Ducted Systems
CONDENSATE DRAIN
A condensate trap must be installed in the condensate drain. The
plumbing must conform to local codes.
Use Teflon tape or pipe thread compound if needed.
SERVICE ACCESS
Access to all serviceable components is provided at the following loca-
tions:
• Coil guards
• Unit top panel
• Corner posts
• Blower access panel
• Control access panel
• Indoor coil access panel
• Compressor access panel
Refer to Figure 3 for location of these access locations and minimum
clearances in Table 4.
Refer to Figure 12 for the R-410A Quick Reference Guide.
THERMOSTAT
The room thermostat should be located on an inside wall approximately
60" above the floor where it will not be subject to drafts, sun exposure
or heat from electrical fixtures or appliances. Sealant should be used
behind thermostat to prevent air infiltration. Follow manufacturer's
instructions enclosed with the thermostat for general installation proce-
dure. Color coded insulated wires (minimum #18 AWG) should be used
to connect thermostat to unit. See Figure 6. Do not use power stealing
thermostats.
POWER AND CONTROL WIRING
Field wiring to the unit must conform to provisions of the current N.E.C.
ANSI/NFPA No. 70 or C.E.C. and/or local ordinances. The unit must be
electrically grounded in accordance with local codes or, in their
absence, with the N.E.C./C.E.C. Voltage tolerances which must be
maintained at the compressor terminals during starting and running
conditions are indicated on the unit Rating Plate and Table 1.
The wiring entering the cabinet must be provided with mechanical
strain relief.
A fused disconnect switch should be field provided for the unit. If any of
the wire supplied with the unit must be replaced, replacement wire must
be of the type shown on the wiring diagram.
Electrical service must be sized properly to carry the load. Each unit
must be wired with a separate branch circuit fed directly from the main
distribution panel and properly fused.
Refer to Figures 6-7 for typical field wiring and to the appropriate unit
wiring diagram for control circuit and power wiring information.
Single point wiring requires the use of the single point wiring kit acces-
sory.
Unit comes wired for 230 volt power. If supply power is 208 volt, wires
connected to the control transformer 230V tap must be moved to the
208V tap.
CAUTION
Hand tighten only.
WARNING
Wear safety glasses and gloves when handling refrigerants. Failure
to follow this warning can cause serious personal injury.
CAUTION
This system uses R-410A Refrigerant which operates at higher pres-
sures than R-22. No other refrigerant may be used in this system.
Gage sets, hoses, refrigerant containers and recovery systems must
be designed to handle R-410A. If you are unsure, consult the equip-
ment manufacturer. Failure to use R-410A compatible servicing
equipment may result in property damage or injury.
!
!
!
FIGURE 6:
Typical Field Control Wiring Diagram for Air Conditioner
Models
FIGURE 7:
Typical Field Power Wiring Diagram
NOTICE
In some applications, the service disconnects on the electric heat kits
must be rotated 180° so the up position of the disconnect is the ON
position. This service disconnect orientation change is required by
UL1995, Article 26.19 (in reference to all circuit breakers).
THERMOSTAT
NOTE:
Heat Anticipator should be set at 0.35 AMPS for all models
LOW
VOLTAGE
WIRING
LEADS
Minimum wire size of 18 AWG wire should be used for all field
installed control wiring.
RED
GREEN
YELLOW
WHITE
BLUE
R
G
W1
Y
C
A0424-001
W2
BROWN
&217$&725
),(/'6833/,('
',6&211(&7
7+5((
3+$6(
32:(5
6833<
*5281'
/8*
5()(572(/(&75,&$/
'$7$7$%/(6726,=(
7+(',6&211(&7
$
