Johnson Controls PCE4 Series Installation Manual Download Page 20

Page: 20 / 20

Subject to change without notice. Published in U.S.A.

5538117-UIM-B-0319

Supersedes: 5538117-UIM-A-0918

York International Corp.

5005 York Drive

Norman, OK 73069

Measured Amperage

Measured Voltage

Heating return air

dry bulb temperature

Number

of elements

Heating supply air

dry bulb temperature

Air temperature rise

Single Phase

Three Phase

Refrigerant Charge and Metering Device

Subcooling

R-410A

R-22

Discharge line

temperature

Superheat

Discharge pressure

Data plate - lbs / Oz

TXV# / Orifice size

Explain operation of system to equipment owner

Explain the importance of regular filter replacement and equipment maintenance

Clean Up Job Site

Owner Education

Comments and Additional Job Details

Provide owner with the owner's manual

Explain thermostat use and programming (if applicable) to owner

Unit Operation and Cycle Test

Operate the unit through continuous fan cycles from the thermostat, noting and correcting any problems

Operate the unit through cooling cycles from the thermostat, noting and correcting any problems

Job site has been cleaned, indoor and outdoor debris removed from job site

Tools have been removed from unit

All panels have been installed

TXV

Fixed Orifice

Liquid line temperature

Suction pressure

Suction line temperature

Electric heat kit - Model number

Serial number

Rated KW

Heater 1

Heater 6

Heater 3

Heater 5

Heater 2

Heater 4

Heater 1

Heater 4

Heater 2

Heater 5

Heater 3

Heater 6

Electric Heat

Summary of Contents for PCE4 Series





















Search results

Summary of Contents for PCE4 Series

Reviews:

Related manuals for PCE4 Series

Brands by name

Popular brands

Johnson Controls PCE4 Series, Installation Manual

Search results

Summary of Contents for PCE4 Series

Reviews:

Related manuals for PCE4 Series

Brands by name

Popular brands