background image

Johnson Controls Ducted Systems

5538117-UIM-B-0319

®

®

SINGLE PACKAGE 
AIR CONDITIONER / ELECTRIC HEAT

MODELS: PCE4 SERIES

3 THRU 5 TONS – 208/230V - 3 PHASE

INSTALLATION MANUAL

LIST OF SECTIONS

GENERAL INFORMATION  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SAFETY  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
MODEL NUMBER NOMENCLATURE  . . . . . . . . . . . . . . . . . . . . . . . 2
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
AIRFLOW PERFORMANCE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

OPERATION   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
MAINTENANCE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
TYPICAL WIRING DIAGRAMS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
START UP SHEET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

LIST OF FIGURES

Component Location   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Unit 4 Point Load Weight  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unit Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Bottom Duct Dimensions (Inches)  . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rear Duct Dimensions (Inches)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Typical Field Control Wiring Diagram for Air Conditioner Models   . . . 6

Typical Field Power Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Single Point Wiring Kit   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Measuring External Static Pressure  . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connection Wiring Diagram  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ladder Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
R-410A Quick Reference Guide  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

LIST OF TABLES

Unit Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Weights and Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unit Dimensions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unit Clearances  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Single Point Kit Numbers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical Data for 208/230-3-60 Single Source Power  . . . . . . . . . . . 8
Electrical Data for 208-3-60 Multi Source Power  . . . . . . . . . . . . . . . . 8
Electrical Data for 230-3-60 Multi Source Power  . . . . . . . . . . . . . . . . 9

Physical Data  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Airflow Performance - Side Duct Application   . . . . . . . . . . . . . . . . . . 11
Airflow Performance - Bottom Duct Application  . . . . . . . . . . . . . . . . 12
Electric Heat Minimum Supply Air   . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Electric Heat Multipliers   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Additional Static Resistance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Thermostat Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

SECTION I: GENERAL INFORMATION

PCE units are factory assembled air conditioners designed for outdoor
installation on a roof top or a slab. Field-installed electric heater acces-
sories are available to provide electric heat.

The units are completely assembled on rigid, removable base rails. All
piping, refrigerant charge, and electrical wiring is factory installed and
tested. The units require only electric power and duct connections at
the point of installation.

SECTION II: SAFETY

This is a safety alert symbol. When you see this symbol on
labels or in manuals, be alert to the potential for personal
injury.

Understand and pay particular attention to the signal words 

DANGER

,

WARNING

, or 

CAUTION

DANGER 

indicates an 

imminently

 hazardous situation, which, if not

avoided, 

will result in death or serious injury

.

WARNING 

indicates a 

potentially

 hazardous situation, which, if not

avoided, 

could result in death or serious injury

.

CAUTION 

indicates a potentially hazardous situation, which, if not

avoided 

may  result  in  minor  or  moderate  injury.

 It is also used to

alert against unsafe practices and hazards involving only property dam-
age.

 WARNING

Improper installation may create a condition where the operation of
the product could cause personal injury or property damage.
Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Failure to carefully read and
follow all instructions in this manual can result in furnace mal-
function, death, personal injury and/or property damage. 
Only a
qualified contractor, installer or service agency should install this
product.

 CAUTION

This product must be installed in strict compliance with the installa-
tion instructions and any applicable local, state, and national codes
including, but not limited to building, electrical, and mechanical
codes.

!

!

Summary of Contents for PCE4 Series





















Reviews: