manualshive.com logo in svg

JING JIE UniPBX-2000, Administrative Manual

Share
Download
JING JIE UniPBX-2000 Administrative Manual Download Page 96

 

 

96

Parameter

Name

Description

Disable Video Call

Whether to allow video call to be madden or not?

Enable Distinctive
Ringing

Whether enable or disable distinctive ringing feature? This
feature need a compatible SIP phone to support this
feature.

2.3.2.1.1  Follow  Me

The follow me time should be defined here when

 Follow Me 

service was enabled in

Call Feature

. Click 

Follow Me

 button to set the following me period and number as

follows:

The detail of each parameter is described as below:

Parameter

Name

Description

Start Time

The  start time (24 hours format) to enable this follow me
number. Earlier than this time, this follow me number will be
ignored. You can also click the "All the Time" for whole day
service.

Stop Time

The stop time (24 hours format) to enable this follow me
number. Over this time, this follow number will be ignored. 
You can also click the "All the Time" for whole day service.

Weekday

The applied weekday for this following me number.

Follow Number

The telephone  number to be followed when the time is in
between start and stop time.

Summary of Contents for UniPBX-2000




























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands