JING JIE UniPBX-2000 Administrative Manual Download Page 124

Page: 124 / 219

124

The detail of each parameter is described as below:

Parameter Name

Description

Device Name

The name to be selected in the dedicate device of
extension.

User Agent

The SIP "User Agent" header used to be filtered for
dedicate device.

Auto Provisioning

Whether enable auto provisioning feature for this device
or not. (1.4 or above only)

Brand Name

The brand name of this device

Model Name

The model name of this device

Number of Lines

Number of lines supported for this device. The default is 1.

Model Template

The model template will be used for this device

Device Template

The device template will be used for this device

Model Configuration
File

The model configuration file for this device if it is
supported.

Device Configuration
File Format

The file naming format for this device

Customized
Command

Special command required to generate configuration file
for this device

Conf Check Interval
(mins)

The interval for the device to refresh or get the new
configuration.

Latest Model
Firmware

Newest firmware will be used for this device

Summary of Contents for UniPBX-2000




























































































































































































































Search results

Summary of Contents for UniPBX-2000

Reviews:

Brands by name

Popular brands

JING JIE UniPBX-2000, Administrative Manual

Search results

Summary of Contents for UniPBX-2000

Reviews:

Brands by name

Popular brands