OM131
79
P1939-OM-131 R11
Chapter 4
To replace the scrubber door and set the torque, proceed as follows:
1.
Remove the old scrubber door from the Backpack.
2.
Lightly lubricate the main O-ring (Fig 4.9, Item 7) on the new scrubber door using an oxygen
compatible lubricant (e.g. Christo-lube fluorinated grease - Divex Part No SM034).
3.
Install the new scrubber door into the Backpack and tighten it lightly to just 'finger tight' only.
4.
Fit the special torque adapter tool (Divex Part No. TA51193) (Fig 4.10) to the handwheel
assembly.
5.
Using an appropriate torque wrench, tighten clockwise until a torque of 2.7 to 2.9 Nm (24 to
26 lb-in) is reached.
6.
Mark the inside of the handwheel outer rim with white paint, in line with the white side of the
tommy bar.
7.
If this is a new setting on a door that has previously been marked, always remove the existing
mark with wire wool or similar abrasive material.
8.
If further guidance is required, please see P1939-PGN-6774.
N
OTE
If the main assembly is removed the screw (Fig 4.9, Item 9) must be fixed in place using a thread
retainer compound.
Fig 4.10 Torque Adapter Tool - TA51193
4.5.2
Upper penetrator replacement
4.5.2.1
Counterlung and demand valve penetrators
1.
Release the wing nut and remove the thermal regenerator.
2.
Using the duct spanner (Divex Part No. M2921B) engaged in upper penetrator slots and the
locknut spanner (Divex Part No. M2920) from the Tool and Test Kit, undo the locknut (Fig
4.11, Item 2 & Fig 4.1, Item 15) and remove.
3.
Push down on the upper penetrator to break the hold of the silicone sealant and remove.
Summary of Contents for Divex SLS Mk IV
