janitza RCM 202-AB User Manual And Technical Data Download Page 9

Page: 9 / 68

www.janitza.de

RCM 202-AB

RCM 202-AB

ATTENTION

Use of the device requires sufficient knowledge of the product as well as

knowledge about the connected devices and systems. Changes to the pre-

set values and control commands influence the evaluation behavior of the

residual current measurement device. Therefore changes to the commis-

sioning settings as well as the replacement of devices may only be carried

out upon agreement with Janitza electronics GmbH!
Changes carried out are to be documented in the system documentation!

Observe the user manual!

This user manual as well as the device-specific user manuals for connected

devices must be strictly observed.

NOTE

The RCM 202-AB is supplied as a component of a residual and operating

current monitoring system. Upon commissioning/delivery of a monitoring

system, all system-specific settings and control commands for the RCM

202-AB shall be parameterized and documented by Janitza electronics

GmbH.

Purpose - Intended use

The RCM 202-AB is a two-channel residual current measurement device for the

measurement and monitoring of main distribution boards up to a maximum residual

current of 20

With connected current measurement transformers (also current sensors), the RCM

202-AB is used for the measurement and monitoring of residual currents in TN and

TT systems (grounded AC systems).
With additional devices of the RCM series, display devices or devices for data cou-

pling to third-party systems, it forms a complete residual and operating current moni-

toring system. This monitoring system increases system and operational safety.

Faults or an increase in residual currents (usually creeping) are detected early on, for

example, thus allowing preventative maintenance. The external signal current circuits

used in the monitoring system shall be secondary current circuits.
Any use of the RCM 202-AB that differs from the description in this manual is consid-

ered improper use and may affect the protection provided by the device.

Summary of Contents for RCM 202-AB





































































Search results

Summary of Contents for RCM 202-AB

Reviews:

Related manuals for RCM 202-AB

Brands by name

Popular brands

janitza RCM 202-AB, User Manual And Technical Data

Search results

Summary of Contents for RCM 202-AB

Reviews:

Related manuals for RCM 202-AB

Brands by name

Popular brands