JAI SW-8000Q-10GE, User Manual

Page: 51 / 74

Setting range Default value Description
Configure image format settings.
ー 8192 Display the maximum image width.
ー 4096 Display the maximum image height.
BinningHorizontal 1:
16〜8192 step 16
BinningHorizontal 2:
8〜4096 step 8 8192 Set the image width.
1 〜 4096 step 1 1 Set the image height (number of lines).
Image data with the specified number of lines will be streamed as 1 block.
BinningHorizontal 1:
0 〜 8176 step 16
BinningHorizontal 2:
0 〜 4088 step 8 0 Set the horizontal offset.
0 〜 4095 0 Set the vertical offset.
1,2 1 Set the number of pixels in the horizontal direction for which to perform
binning. BinningMode is fixed to Sum.
1,2 1 Set the number of pixels in the vertical direction for which to perform
binning. BinningMode is fixed to Sum.
RGB, NIR RGB Select the component.
PixelFormat ー RGB8 Set the pixel format.
[Setting Range]
[Component Selector = RGB]
RGB8 (Default), RGB10V1Packed, RGB10p32
YUV422_8_UYVY, YUV422_8
RGBA8
[Component Selector = NIR]
Mono8 (Default) , Mono10Packed
*) In Component Selector = RGB, when PixelFormat is set RGBA8,
Pixel Format in ComponentSelector = NIR is invalid.
Off,
White,
GrayPattern1(Ramp),
GrayPattern2(Stripe),
ColorBar Off Select the test image.
Off, On Off Invert the image left and right.
Setting range Default value Description
Configure image capture settings.
Single Frame,
Multi Frame,
Continuous Countinuous Select the image capture mode.
ー ー Start image capture.
ー ー Stop image capture.
1〜65535 1 In [MultiFrame] mode, set the number of frames to capture.
ー 66 Display the frame rate as a frequency. (unit: Hz)
66 〜 66 Set the AcquisitionLineRate (Hz).
The maximum value varies depending on the PixelFormat and ROI settings.
ー Acquisition Start Select the trigger operation.
[Setting range]
Acquisition Start, Acquisition End, Line Start, Frame Start, Frame Transfer Start
TriggerMode Off, On Off Select the trigger mode.
TriggerSource ー Line4 TTL In 1 Select the trigger signal source.
[Setting range]
PulseGenerator0, PulseGenerator1, PulseGenerator2, PulseGenerator3
UserOutput0, UserOutput1, UserOutput2, UserOutput3
Action 0, Action 1, Action 2, Action 3
Line4 TTL In 1, Line5 Opt In 1, Line10 TTL In 2, Line13 TTL In 3
Logical Block 0, Logical Block 1, Encoder Trigger
TriggerActivation RisingEdge,
FallingEdge,
Level High,
Level Low Rising Edge Select the polarity of the trigger signal (i.e., location of signal at which
trigger is applied).
[Trigger Selector] = Line Start
ExposureMode is Off or Timed : RisingEdge, Falling Edge
ExposureMode is TriggerWidth : LevelHigh, LevelLow
Off, Timed, Trigger Width Timed Select the exposure mode.
Common, Individual Common Select the exposure time mode.
ExposureTimeMode:Common
Common,
ExposureTimeMode:Individual
Red,
Green,
Blue
Common Select the sensor to set ExposureTime.
To set the common setting values for all three sensors, select Common
ExposureTime 3 〜 15149 Set the exposure time.
Off, On Off When set to On, you can change Green while maintaining white balance.
ExposureTimeSelector
RBExposureInterlocked
Item
WidthMax
HeightMax
Width
BinningHorizontal
OffsetY
OffsetX
b） ImageFormatControl
Horizontal Image Mirroring
Acquisition Stop
Acquisition Start
Acquisition Mode
TestPattern
SensorBinningVertical
ExposureTimeMode
Item
ComponentSelector
Trigger Selector
Acquisition Frame Rate(Hz)
Height
Acquisition Frame Count
ExposureMode
c） Acquisition Control
Acquisition Line Rate
SW-8000Q-10GE/SW-8000Q-SFP
— 5 1 —