31
value from a minimum of 15 °C to a maximum of 40 °C (59÷104 °F).
NOTE:
- Press and hold the button down until you reach the desired val-
ue; by releasing the button and pressing it again, the adjustment is
made in the opposite direction.
-
During operation of the heater, the light spot on the screen next to
the temperature value flashes.
X
To show the temperature of the water in the tub again, do
not touch any key for about 5 seconds.
Models equipped with a Jacuzzi® CoolPower heat pump
- The heating is switched off (
the filtration pump remains on for 30
seconds
) as soon as the water temperature set-point is exceeded
(by about 1 °C), and is not switched on again until the temper-
ature does not drop by about 1.5 °C compared to the set-point.
X
To ensure precise measurement of the water temperature,
the filtering pump is turned on, approximately every half an
hour for 30 seconds
(even if filtering cycles are not set)
.
When the system is turned off, or there is a power outage, the last
set point is stored in memory.
When heating is in operation, the LED located under the
sym-
bol comes on (if it flashes, this means that heating has been paused,
so as not to exceed the maximum permitted consumption; see the
information at the beginning of the chapter).
CAUTION
Do not use the hot tub if the water temperature is 40 °C
or more.
Q
M
AINTENANCE
OF
MINIMUM
TEMPERATURE
OF
WATER
IN
TUB
AND
ANTI
-
FREEZE
PROTECTION
OF
THE
PIPES
(“S
MART
W
INTER
”).
“Smart Winter” mode lets you make use of a special probe to
monitor the temperature of the compartment under the tub, which
contains the all of the pipes of the plumbing circuit. In extreme con-
ditions, the system may turn on this protection (indicated on the
display by the message
ICE
), switching on the pump(s).
ATTENTION: In the case of particularly low temperatures
specifically, check the electrical power supply regularly to
ensure that the function is not interrupted.
X
The pumps are turned on at pre-set intervals:
- temperature between 12 and 15 ° C (54 - 59 °F):
every 2 hours
- temperature between 9 and 12 ° C (48 - 54 °F):
every hour
- temperature between 6 and 9 ° C (42 - 48 °F):
every 30 minutes
- temperatures at or below 6 ° C (42 °F):
every 15 minutes
NOTES
- If the temperature of the compartment drops rapidly, the frequen-
cy of activation increases.
- If it becomes necessary to turn on the anti-freeze protection during
a filtering cycle, these will be suspended and resume when the cycle
is complete.
- If it is necessary to perform an anti-freeze cycle while a function
activated by the user is in progress, the cycle will be activated 15
minutes after the end of the function.
- If this protection is active, the spotlight may still be turned on.
Q
“E
NERGY
SAVINGS
”
MODE
(“
ECO
”
FUNCTION
)
When this function is on, the water heater only turns on again when
the temperature drops to approximately 10°C (50°F) below the set-
point.The minimum permitted temperature is 15°C.
X
Press the “
Up/Down
”
button (display B): the current tem-
perature is displayed.
X
While the LED above the thermometer symbol is on, hold
down the “
Light
”
button for approximately 5 seconds: when
the button is released the screen briefly shows the new refer-
ence value alternated with the word "Eco"; then, the current
temperature will appear again.
X
To turn the function off, proceed as indicated above (press
the “
Up/Down
”
button, etc.).
NOTE:
- To check the function status
, press the “
Up/Down
”
button: if
“Eco” appears, the function is on.
Water filtering
The water needs to be filtered to keep it clean and clear. This option
is active during the day as follows:
- two filtration cycles that are repeated every 12 hours.
Each filtration cycle is has an initial phase, in which the pump
is turned on one at a time for approximately one minute; then
the cycle continues, activating the Clearray™ Pro3tect™ and the
filtration pump for the remaining time.
Q
S
ETTING
THE
FILTERING
CYCLES
To set the filtering cycle:
X
Hold down the “
Pump
”
button (display B) for approxi-
mately 5 seconds:
dx
(where “x” indicates the duration in hours)
appears on the screen.
X
Use the “
Up/Down
”
button to enter the desired duration
(from a minimum of 0 to a maximum of 12 hours)
.
Summary of Contents for Skylounge
