manualshive.com logo in svg

IWILL DN800-L, User Manual, Page: 7 / 60

Share
Download
IWILL DN800-L User Manual Download Page 7

 

 
IWILL DN800-SATA/-L Series                                                          7 

DN800-SATA/DN800-L Package Content 

 

1. DN800-SATA/DN800-L Motherboard 

 

Professional workstation system board 

2. Three jumper caps   

 

Extra caps in case original caps get lost 

3. One Power Installation CD 

 

Includes support software, drivers and bundled software utilities.

 

4. Rear panel I/O shield   

 

Covers the area around the rear panel I/O ports when the board is installed in a 

system housing.

 

5. Two sets of SATA cables 

 

Connector cable for onboard SATA connectors. (DN800-L only one set)

 

6. Two ATA-66/100 IDE cables 

 

Connects IDE devices to one of the onboard IDE connectors.

 

7. One floppy disk drive cable 

 

Connects floppy disk drives to the onboard floppy disk connector.

 

8. Two Hat Springs for CPU cooler 

 

Sustain and connect between CPU cooler and chassis 

9. One iron backplate 

 

The iron backplate connects the motherboard and chassis, and sustain the mass of 

CPU heatsink. 

10. Two CPU Plastic backplates

 

 

It can fix the third party CPU heatsink. Please refer to Chapter 3 for detail 

information. 

11. Two heatsink retention modules 

 

It can buckle up the CPU heatsink. Please refer to Chapter 3 for detail information. 

IWILL 

                                                                                                                 

User’s Manual

Summary of Contents for DN800-L





























































Reviews:

No comments