manualshive.com logo in svg

IWILL DN800-L, User Manual, Page: 52 / 60

Share
Download
IWILL DN800-L User Manual Download Page 52

DN800-SATA/-L Motherboard                                                                                                                IWILL 

 
52                                                        IWILL DN800-SATA/-L Series 

Advanced Menu 

 

You can make these modifications on the Advanced Menu. Select the Submenus to 

modify those settings. 

 

 

CPU Configuration

 

Configure CPU Setting 

 

IDE Configuration

 

Configure IDE Setting 

 

Floppy Configuration

 

Configure floppy Setting 

 

SuperIO Configuration

 

Configure Super IO chipset setting 

 

Hardware Health Configuration

 

Monitor Hardware Health 

 

ACPI Configuration

 

Configure ACPI Setting 

 

MPS Configuration

 

Configure Multi-Processors Table 

 

PCI-Express Configuration

 

Configure PCI-Express support 

 

Remote Access Configuration

 

Configure Remove Access Setting 

 

USB Configuration

 

Configure USB Setting 

 

Onboard Device Configuration

 

Configure onboard device, such as Silicon 3114 and NEC USB, Setting 

 

Performance Setting

 

Summary of Contents for DN800-L





























































Reviews:

No comments