IVT CSD-12, Manual Instruction

Page: 9 / 84

9
Manual instruction
EN
Be familiar with the controls and the proper use of
the tool before attempting to use it and above all,
make sure you know how to stop to use it in case
of emergency.
Following these simple instructions will also
maintain your tool in good working order.
• The tool must be assembled correctly before use.
• Only use the tool for its designed purposes.
• In addition to the design of the tool there may
be safety decals that must be considered and
indications about the safety equipment to use.
The prevention of accidents is dependent upon
the awareness, common sense and proper training
of everyone involved in the operation, transport,
maintenance and storage of the tool.
• Never leave the tool unattended.
• Never allow children to use the tool. Children
should be supervised to ensure that they do not
play with the tool.
• Keep children and pets away. All onlookers
should be kept at a safe distance away from the tool
when it is in use.
• The user is responsible for third parties while
working with the tool .
• People who aren’t acquainted with the operating
instructions, children, juveniles who have not yet
reached the minimum age for using this tool and
people under the influence of alcohol, drugs or
medication are not allowed to use the tool . Local
regulations may restrict the age of the operator.
WARNING: The consumption of alcohol,
medication and drugs, plus states of
illness, fever and fatigue will affect your
ability to react. Do not use this tool in any of these
situations.
• Make sure that all the protective devices (if
present) are fitted and are in good condition.
• Never operate the tool with defective safety
devices or guards (if present), or without safety
devices in place .
• Inspect the entire tool to look for loose parts
(e.g. nuts, bolts, screws, etc.) and for any damage.
Check at frequent intervals if screws and bolts
are properly tight to be sure the equipment is in
safe working condition. Repair or replace them, if
necessary, before using the tool. Serious injury to
the operator and to the bystanders could result if
there’s a damage to the tool .
• While using the tool, dress properly. Do not
wear loose clothing or jewelry that could become
caught by the tool. Wear suitable working clothes. It is
recommended that legs and feet are covered, to protect
from flying debris. Long air should be tided back.
• Keep handles and grips dry, clean and free from
oil and grease.
• Use a proper protective equipment. Use
safety glasses and safety gloves. Also use a dust
mask during pulverulent operations or if exaust
gases are present. When necessary, use also non-
slipping boots or shoes, hardhat and earplugs. If
the noise level exceeds 85 dB(A), ear protection is
obligatory.
WARNING! Use personal protective
equipment! Safety devices and the
personal protective equipment protect
your own health and the health of others and
ensure a trouble-free operation of the tool .
• Do not start to use the tool if it is in an inverted
position or it is not in the right working order.
• Ensure that you have a good stand, while you
operate with the tool. Keep proper footing and
balance at all times.
• Keep work area clean. Cluttered areas invite
injuries. Before use, all foreign bodies must be
removed from the working area, also pay attention
to foreign objects during the operation.
• Do not force the tool.
• Only work in daylight or sufficiently good
artificial light. Never operate the tool without good
visibility.
• Be careful not to drop the tool or hit it against
obstacles.
Stay alert. Watch what you are doing.
Distraction can cause you to lose
control. Use common sense.
Electrical safety rules
ATTENTION! When using electrical tools,
the following safety instructions should
be observed to prevent the risk of
electric shock, personal injury and fire. Read and
observe these instructions carefully before using
the tool.
• It is recommended for increased electrical
safety to use a Residual Current Device (RCD) with
a tripping current of not more than 30 mA. Always
check your RCD every time you use it. Consult a
reliable electrician.
WARNING! The use of an RCD or other
circuit breaker unit does not release the