ITT HT 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 81 | Manualshive

Page: 81 / 148

background image

228A

241

370F

370D

423

134

370C

2. Remove the clamp screws (370C) and back off the jam nuts (423).
3. Tighten the jack screws (370D) evenly to move the bearing housing (134) out of the bearing frame

(228A).

4. Remove the shaft assembly from the bearing frame (228A).
5. Remove the jack screws (370D), the nuts (423), and the bearing housing O-ring.
6. Remove the inboard bearing (168A).

122

168A

248A

112A

136

382

253B

7. Remove the bolts (371C), the bearing end cover (109A), and the gasket (360C).
8. Remove the outboard labyrinth oil seal (332A) from the end cover (109A).
9. Remove the O-rings (497F and 497G) if it is necessary.

Labyrinth oil-seal O-rings are part of the 3196 maintenance kits, and they are sold separately.

109A

332A

371C

360C

10. Remove the bearing housing (134) and the bearing (112A) from the shaft (122).

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

79

«
...
79
80
81
82
83
...
»

Summary of Contents for HT 3196 i-FRAME





















































































































































Reviews:

No comments

Related manuals for HT 3196 i-FRAME

Brand: Gardena Pages: 17

Brand: EBARA Pages: 40

Brand: EBARA Pages: 534

Brand: EBARA Pages: 60

Brand: ebm-papst Pages: 8

Brand: Enviroheat Pages: 20

Brand: Enviroheat Pages: 29

Brand: Waterax Pages: 6

Brand: DROPSA Pages: 9

Brand: DAB Pages: 72

Brand: Bravo Pages: 12

BASITRONIC CDX 11-U

Brand: clage Pages: 32

Alterma EDHQ011AA6V3

Brand: Daikin Pages: 22

Brand: Becker Pages: 4

Brand: KlimaTeknik Pages: 16

Brand: Zenit Pages: 24

Brand: Pentair Hydromatic Pages: 20

Brand: York Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands