ITT HT 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 15 | Manualshive

Page: 15 / 148

background image

NOTICE: When lifting a unit that does not have a way to secure the strap on the suction flange, you must
secure the strap around the frame adapter. Failure to do so may result in equipment damage.

Figure 4: Example of a proper lifting method with a strap secured around the frame adapter

Storage guidelines

Pump storage requirements

Storage requirements depend on the amount of time that you store the pump. The normal packaging is
designed only to protect the pump during shipping.

Length of time in storage

Storage requirements

Upon receipt/short-term (less than six months)

• Store in a covered and dry location.
• Store the unit free from dirt and vibrations.

Long-term (more than six months)

• Store in a covered and dry location.
• Store the unit free from heat, dirt, and

vibrations.

• Rotate the shaft by hand several times at least

every three months.

NOTICE:
Risk of damage to the mechanical seal or shaft sleeve on units supplied with cartridge mechanical seals.
Make sure to install and tighten the centering clips and loosen the set screws in the seal locking ring.

Treat bearing and machined surfaces so that they are well preserved. Refer to drive unit and coupling
manufacturers for their long-term storage procedures.

Frostproofing

Table 2: Situations when the pump is or is not frostproof

Situation

Condition

Operating

The pump is frostproof.

Immersed in a liquid

The pump is frostproof.

Lifted out of a liquid into a temperature below

freezing

The impeller might freeze.

Transportation and Storage

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

13

«
...
13
14
15
16
17
...
»

Summary of Contents for HT 3196 i-FRAME





















































































































































Reviews:

No comments

Related manuals for HT 3196 i-FRAME

Brand: GE Pages: 28

Brand: 4rain Pages: 44

Brand: Danfoss Pages: 22

Brand: Calpeda Pages: 72

LEADER ECOTRONIC Series

Brand: DAB PUMPS Pages: 10

Brand: Nakayama Pages: 29

Brand: GEA Pages: 66

Brand: QED Pages: 33

Pacific Hydrostar 2" or 3" Dirty Water Pump...

Brand: Pacific hydrostar Pages: 36

LARIUS VEGA 5:1

Brand: Samoa Pages: 28

Brand: Seisco Pages: 20

Brand: A.O. Smith Pages: 20

Brand: Gude Pages: 64

Brand: Wayne Pages: 4

Brand: Altrad Pages: 30

DIESELFI Series

Brand: FMT Pages: 14

Brand: Becker Pages: 4

Brand: JABSCO Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands