ITT HT 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 97 | Manualshive

Page: 97 / 148

background image

122

168A

253B

382

136

112A

9. Install the bearing housing as follows (see the illustration):

a) Coat the outside of the outboard bearing (112A) with oil.
b) Coat the bore of the bearing housing (134) with oil.
c) Put the bearing housing (134) onto the shaft.

Do not use force.

122

253B

134

112A

168A

10. Prepare the shaft for assembly as follows (see the illustration):

a) Place the bearing-clamp ring (253B) onto the shaft (122).
b) Fasten the clamp-ring bolts (236A) crosswise.

See the specified torque values.
Make sure that the shaft rotates freely.

c) Install a new O-ring (496).
d) Install the outboard labyrinth oil-seal (332A) into the bearing housing (134).

Place the drain slots of  the oil seal at the bottom position (6 o’clock).
Make sure that the edges of  the keyway are free from burrs. To protect the O-ring, cover the
keyway lengthwise with a piece of  electrical tape before you install the oil seal.

236A

253B

134

332A

496

11. Install the shaft assembly into the bearing frame as follows (see the illustration):

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

95

«
...
95
96
97
98
99
...
»

Summary of Contents for HT 3196 i-FRAME





















































































































































Reviews:

No comments

Related manuals for HT 3196 i-FRAME

Brand: Nakayama Pages: 8

Brand: Eccotemp Pages: 90

Brand: Eccotemp Pages: 40

Brand: Eccotemp Pages: 19

Brand: Quooker Pages: 12

geoTHERM SERIES

Brand: Vaillant Pages: 112

geoTHERM SERIES

Brand: Vaillant Pages: 132

Pure Link 1300 Series

Brand: lancer Pages: 20

Brand: Zehnder Pumpen Pages: 32

Brand: T.I.P. Pages: 136

BASIC VASF 2.120/1-0.AC115

Brand: Becker Pages: 6

Brand: Noritz Pages: 26

Brand: Barnes Pages: 16

MULTIDRAIN UV 305-1

Brand: Pentair Jung Pumpen Pages: 40

Brand: Pitco Pages: 20

Brand: Laars Pages: 20

Cylinder DuroTech MAP07

Brand: Milwaukee Pages: 20

Brand: Zodiac Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands