ITT HT 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 107 | Manualshive

Page: 107 / 148

background image

228A

134

370D

423

370C

Assemble the frame

1. Support the frame assembly in a horizontal position.
2. Check the shaft-end play by moving the shaft forward and backward by hand, and note any indicator

movement.
If the total indicator reading is greater than the values in this table, then disassemble the shaft and
determine the cause.
Use this table as a reference for shaft-end play values.

Table 14: Shaft-end play

Frame

Double row bearing

Duplex bearing

STi inches (millimeters)

0.0011 (0.028)
0.0019 (0.048)

0.0007 (0.018)
0.0010 (0.025)

MTi inches (millimeters)

0.0013 (0.033)
0.0021 (0.053)

0.0009 (0.023)
0.0012 (0.030)

LTi inches (millimeters)

Not applicable

0.0010 (0.025)
0.0015 (0.038)

XLT-i inches (millimeters)

0.0014 (0.036)
0.0023 (0.058)

0.0010 (0.025)
0.0015 (0.038)

SCALE

0.160

3. Check the shaft-sleeve (126) runout.

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

105

«
...
105
106
107
108
109
...
»

Summary of Contents for HT 3196 i-FRAME





















































































































































Reviews:

No comments

Related manuals for HT 3196 i-FRAME

PELLEMATIC SmartXS

Brand: MAINE ENERGY SYSTEMS Pages: 82

Brand: Wayne Pages: 8

Brand: Balcrank Pages: 18

Brand: Bryant Pages: 26

Delta Solo Compact MVP Series

Brand: KSB Pages: 40

Brand: Goodman Pages: 16

Brand: Endress Pages: 17

PERFECT 350 ELECTRONIC

Brand: Wijas Pages: 9

SCP 16000 IQ Level Sensor

Brand: Kärcher Pages: 76

Brand: GORMAN-RUPP PUMPS Pages: 31

Brand: Fairland Pioneer Pages: 36

Brand: SAER Elettropompe Pages: 44

Brand: Sanden Pages: 48

BlackFin CT-2902BPHP

Brand: Panduit Pages: 68

Brand: Vallfirest Pages: 32

Brand: Xylem Pages: 28

Brand: Wacker Neuson Pages: 208

Brand: GORMAN-RUPP PUMPS Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands