ITT HT 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 49

Page: 49 / 148

If the pump size is... Then...
XLT-i

1. Align the end plate on the pump side to the bearing housing so that

you meet these conditions:
a.

The large slots on the end plate do not touch the bearing housing
tap bolts.

b. The small slots align with the impeller adjusting bolts.

2. Fasten the end plate to the bearing housing using the jam nuts on the

impeller adjusting bolts.

3. Check the impeller clearance. Refer to the impeller clearance table for

the correct impeller clearance.

Driver

Pump end plate

Bearing housing

Jam nut

3. Put the pump-half of the coupling guard in place:

a) Slightly spread the bottom apart.
b) Place the coupling guard half over the pump-side end plate.

Commissioning, Startup, Operation, and Shutdown

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for HT 3196 i-FRAME





















































































































































Search results

Summary of Contents for HT 3196 i-FRAME

Reviews:

Related manuals for HT 3196 i-FRAME

Brands by name

Popular brands

ITT HT 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for HT 3196 i-FRAME

Reviews:

Related manuals for HT 3196 i-FRAME

Brands by name

Popular brands