ITT HT 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 113

Page: 113 / 148

5. Set the impeller clearance.

Refer to the Impeller clearance setting topic for more information.

6. Tighten the setscrews in the seal locking ring in order to secure the seal to the shaft.
7. Remove the centering clips from the seal.

Seal the shaft with a conventional inside-component mechanical seal

WARNING:
The mechanical seal used in an Ex-classified environment must be properly certified. Prior to startup,
make sure that all areas that could leak pumped fluid to the work environment are closed.

NOTICE:
The mechanical seal must have an appropriate seal-flush system. Otherwise, excess heat generation and
seal failure can occur.

1. Assemble the seal chamber:

a) Install a seal-chamber cover or a backplate (184) and fasten with nuts (370H) with .

370H

184

b) Check the seal-chamber cover runout.

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

111

Summary of Contents for HT 3196 i-FRAME





















































































































































Search results

Summary of Contents for HT 3196 i-FRAME

Reviews:

Related manuals for HT 3196 i-FRAME

Brands by name

Popular brands

ITT HT 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for HT 3196 i-FRAME

Reviews:

Related manuals for HT 3196 i-FRAME

Brands by name

Popular brands