ITT HT 3196 i-FRAME Installation, Operation And Maintenance Manual Download Page 88

Page: 88 / 148

Surface inspection locations

This figure shows the areas to inspect for wear on the bearing frame outside surface.

228

Figure 20: Outside surface inspection locations

This figure shows the areas to inspect for wear on the bearing frame inside surface.

241

Figure 21: Inside surface inspection locations

C-face adapter inspection

Checklist

• Visually inspect the C-face adapter (340) for cracks.
• Check all surfaces for rust, scale, or debris and remove all loose and foreign material.
• Check for corrosion or pitting.

This figure shows the areas to inspect for cracks on the C-face adapter.

Figure 22: C-face adapter inspection locations

Maintenance

Model HT 3196 i-FRAME Installation, Operation, and Maintenance Manual

Summary of Contents for HT 3196 i-FRAME





















































































































































Search results

Summary of Contents for HT 3196 i-FRAME

Reviews:

Related manuals for HT 3196 i-FRAME

Brands by name

Popular brands

ITT HT 3196 i-FRAME, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for HT 3196 i-FRAME

Reviews:

Related manuals for HT 3196 i-FRAME

Brands by name

Popular brands