63
64
62
61
MAIN FEATURES: REMOTE UNIT
A LED INDICATOR
Flashes once when the remote unit transmits a reading
Flashes twice when low battery is detected on
sensor unit
B BATTERY COMPARTMENT
Accommodates two AA-size batteries
C RESET BUTTON
Press to reset all setting if you have selected
different channel.
D CHANNEL SELECTOR
Select the channel before you install batteries.
E WALL-MOUNT RECESSED HOLE
Supports the remote until in wall-mounting
F ˚C/ ˚F BUTTON
2. GETTING STARTED
2a) BEFORE YOU BEGIN
For best operation,
1. Insert batteries for remote units before doing so for the
main unit.
2. Position the remote unit and main unit within effective
transmission range, which, in usual circumstances, is
20 to 30 meters.
Note that the effective range is vastly affected by the
building materials and where the main and remote units
are positioned.
Try various set-ups for best result.
Though the remote units are weather proof, they should
be placed away from direct sunlight, rain or snow.
2b) BATTERY INSTALLATION: REMOTE UNIT
1. Remove the screws on the battery compartment.
2. Select the channel
3. Install 2 batteries (UM-3 or “AA” size 1.5V) strictly
according to the polarities shown.
4. Replace the battery compartment door and secure
its screws.
2c) BATTERY INSTALLATION: MAIN UNIT
1. Open the battery compartment door.
2. Install 2 batteries (UM-3 or “AA” size 1.5V) strictly
according to the polarities shown.
3. Replace the battery compartment door.
2d) LOW BATTERY WARNING
When it is time to replace batteries for the remote sensor,
the respective low-battery indicator [ ] will show up on
the outdoor temperature for sensor battery and on the time
display for the main unit.
2e) HOW TO USE THE TABLE STAND
OR WALL MOUNTING
The main unit has a removable table stand, which when
connected, can support the unit on a flat surface. Or you
can remove the stand and mount the unit on a wall using
the recessed screw hole.
SETTING UP THE REMOTE TEMP. AND RC CLOCK
a. Once batteries are in place for the remote unit, they will
start transmitting temperature and humidity readings at
around 45 seconds intervals.
The main unit will also start searching for signals for
about two minutes once batteries are installed. 10
seconds upon successful reception, the outdoors
temperatures and humidity will be displayed .The main
unit will automatically update its readings at about
45-second intervals.
b. If no signals are received, blanks “ ” will be
displayed.
Hold [ ] for 2 seconds to enforce another search for
about 2 minutes. This is useful in synchronizing the
transmission and reception of the remote and main units.
c. When remote signal reception is finished, it will
automatically synchronize its current time and dated
when brought within rang of the “
HBG
” RF signal.
Repeat this step whenever you find discrepancies between
the reading shown on the main unit and that on the
remote unit.
A DISPLAY
Facilitates easy reading of remote and indoors
temperatures and calendar clock
B CHANNEL BUTTON
Display different sensor temperature
C MEMORY [MEN] BUTTON
Recalls the maximum or minimum temperature and
humidity of main and remote unit
D
MODE BUTTON
Toggles the display modes and confirms entry while
setting the values for display
E ALARM BUTTON
Displays the alarm time or sets the alarm status
F SNOOZE / LIGHT BUTTON
Activate the snooze function or LCD backlight
G WALL-MOUNT RECESSED HOLE
For mounting the main unit on a wall
H UP ( ) BUTTON
Advances the value of a setting
I DOWN ( ) BUTTON
Decreases the value of a setting
J BATTERY COMPARTMENTS
Accommodates two UM-3 or “AA” size 1.5V
alkaline batteries
K REMOVABLE TABLE STAND
For standing the main unit on a flat surface
A C
B
D
F
E
RESET
CHANNEL
1 2 3
WIRELESS THERMO
1
