Interroll ZoneControl Operating Manual Download Page 18 | Manualshive

Page: 18 / 54

background image

18 von 54

Version 2.0 (04/2019) Online

Translation of the original operating manual

Product information

3.2

Setup

1 Upstream PTP connector

1)

7 Inputs/outputs connectors

2 Zone sensor connector

8 Downstream PTP connector

1)

3 Start sensor connector

9 Cover for DIP switches

4 RollerDrive connector

10 Marker (changeable)

5 Mounting link with hole for countersunk screw

11 Red and green LED

6 Power supply connector

1)

PTP = Peer-to-peer connection

3.3

Scope of delivery

The ZoneControl contains the following components:
•  ZoneControl
•  Mating plug for power supply (WAGO 734-102/xxx-xxx)
•  Mating plug for power supply (WAGO 734-102/xxx-xxx)
•  Spare tool for power supply mating plug (black)
•  Spare tool for inputs/outputs mating plug (yellow)

«
...
16
17
18
19
20
...
»

Summary of Contents for ZoneControl























































Reviews:

No comments

Related manuals for ZoneControl

Brand: Lattice Semiconductor Pages: 30

Brand: WAFER Pages: 15

Brand: E-fly Pages: 16

Brand: Paratec Pages: 8

Brand: J+J Pages: 33

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Brand: VAT Pages: 39

Brand: Samson Pages: 124

Brand: Samson Pages: 86

Brand: VAC Pages: 5

U1000 iQpump Drive

Brand: YASKAWA Pages: 426

Brand: YASKAWA Pages: 26

Brand: YASKAWA Pages: 210

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 400

Z1000 CIMR-ZU*A Series

Brand: YASKAWA Pages: 466

Saxun Mosquito Screen Lateral Door 2020

Brand: Gimenez Ganga Pages: 2

Brand: Keysight Technologies Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands