Interroll ZoneControl Operating Manual Download Page 4

Page: 4 / 54

4 von 54

Version 2.0 (04/2019) Online

Translation of the original operating manual

Inhalt

Transport and storage

4.1 Transport

4.2 Storage

Assembly and installation

5.1

Warning notices for installation

5.2

Assembling the ZoneControl

5.3

Warning notices for electrical installation

5.4

Electrical installation

Required cables:

Signal status of inputs

Signal status of outputs

Schematics of all outputs

5.5 Sensors

5.6

Inputs and outputs

RollerDrive connection: 8 mm snap-in, 5-pin, pin location in accordance with DIN EN 61076-2

Start sensor connector: WAGO 733-103 mating plug

Zone sensor connector: WAGO 733-103 mating plug

Upstream peer-to-peer connection: RJ45 socket, 8-pin Molex 43860

Power supply connector: WAGO 734-102 mating plug

Inputs/outputs connector: WAGO 733-108 mating plug

Downstream peer-to-peer connector: RJ45 socket, 8-pin Molex 43860

5.7

Wiring diagrams

ZoneControl within the conveyor section

ZoneControl at the start of the conveyor section

ZoneControl at the end of the conveyor section

Connection of the external speed control

Connection of a second RollerDrive

Initial startup and operation

Summary of Contents for ZoneControl























































Search results

Summary of Contents for ZoneControl

Reviews:

Related manuals for ZoneControl

Brands by name

Popular brands

Interroll ZoneControl, Operating Manual

Search results

Summary of Contents for ZoneControl

Reviews:

Related manuals for ZoneControl

Brands by name

Popular brands