Interroll ZoneControl Operating Manual Download Page 46

Page: 46 / 54

46 von 54

Version 2.0 (04/2019) Online

Translation of the original operating manual

Troubleshooting

8.1

Troubleshooting

Symptom

Possible Cause

Help

ZoneControl is not working or is

working incorrectly

No power supply

Check whether the output

voltage of the power supply

is within the specified voltage

range.

Check the connections and

correct if necessary.

Wrong position of the DIP switches

Check and if necessary

correct the position of the DIP

switches (see „DIP switches”,

page 21).

ZoneControl faulty or damaged

Internal fuse triggered or faulty

Replace the ZoneControl.

RollerDrive is not working

RollerDrive is faulty or no power supply

Check whether the output

voltage of the power supply

is within the specified voltage

range.

Check the connections and

correct if necessary.

The ERROR signal is automatically

reset after elimination of the fault

and the ZoneControl immediately

performs a local reinitialisation of

the affected zone.

Conveyor process interrupted

Packages jammed

Remove jammed packages.

The ERROR signal is automatically

reset after elimination of the fault

and the ZoneControl immediately

performs a local reinitialisation of

the affected zone.

Summary of Contents for ZoneControl























































Search results

Summary of Contents for ZoneControl

Reviews:

Related manuals for ZoneControl

Brands by name

Popular brands

Interroll ZoneControl, Operating Manual

Search results

Summary of Contents for ZoneControl

Reviews:

Related manuals for ZoneControl

Brands by name

Popular brands