Chapter 1: Installation
14
CDC4 Door Controller Installation and Programming Manual
(3) Earth terminal. Connect the power earth wire from the enclosure mains transformer to the
earth terminal. Data cable shields can also be connected. See “Local data buses” on page
26.
(4) Battery 1 terminals. See
(5) Battery 2 terminals. See
(6) Auxiliary power output. See
“Auxiliary power terminals” on page 26.
(7) Siren output. See
(8)
ATS system bus. See “System data bus” on page 26.
(9) Tamper switch input. Connect the T and C terminals to the panel tamper switch in the
enclosure. Short circuit for inactive, open circuit for active. Must be shortened if not used.
Can only be used with normally closed contacts such as the panel tamper switches.
(10) Relay and lock power connections
for four doors. Refer to “Door lock relay wiring” on page
(11) Earth terminal.
(12)
Input terminals. See “Inputs” on page 30.
(13)
Output expansion connector. See “Output expansion” on page 30.
(14)
PWR link. Power link for relay expansion cards. See “Output expansion” on page 30.
(15) Micro-B USB port.
(16) Ethernet port.
(17)
Heart beat LED. See “LED indications” on page 32.
(18) Bus 1 quick connect header
. See “Local data buses” on page 26.
(19)
Bus 2 connector. See “Local data buses” on page 26.
(20)
Bus 1 connector. See “Local data buses” on page 26.
(21) Bus 1 quick connect header
. See “Local data buses” on page 26.
(22) Lock power 2 quick connect header
. See “Local data buses” on page 26.
(23) Bus 1 Rx LED. See
(24) Bus 1 Tx LED. See
(25) Bus 1 TERM link. See
(26) Bus 2 Rx LED. See
(27) Bus 2 Tx LED. See
(28) Bus 2 TERM link. See
(29)
System bus Rx LED. See “LED indications” on page 32.
(30)
System bus Tx LED. See “LED indications” on page 32.
(31) System bus TERM link. See
(32) Lock power 1 quick connect header.
See “Local data buses” on page 26.
(33) 10/100 Mbps LED. See
(34) Ethernet link active LED. See
(35) Test links
(not fitted during normal operations). See “Defaulting the door controller” on page
(36) System ready LEDs. See
(37) Address selection DIP switch. Refer to
“DIP switch settings” on page 23.
(38)
Relay coil active LEDs. See “LED indications” on page 32.
Table 1: Connection details for terminal blocks
Terminals
Terminal block
Description
~, ~
AC
Mains transformer: 20 V AC power
Mains transformer: Power earth wire
+, −
BATT 1
12 V battery (the cable is fused)
+, −
BATT 2
12 V battery (the cable is fused)
+12, +12, +12
AUX POWER
Auxiliary power +12 V DC
−, −, −
Auxiliary power GND
S+, S−
OUT
8 Ω siren speaker or two 8 Ω siren speakers in parallel, or
12 V DC device and
1 kΩ 1/4 W resistor
Summary of Contents for CDC4
Page 1: ...CDC4 Door Controller Installation and Programming Manual P N 466 5478 REV D ISS 29OCT19 ...
Page 86: ...Chapter 3 Programming 80 CDC4 Door Controller Installation and Programming Manual ...
Page 120: ...Chapter 4 Menu reference 114 CDC4 Door Controller Installation and Programming Manual ...
Page 136: ...130 CDC4 Door Controller Installation and Programming Manual ...