Innovx FastSwitch Installation & Operation Manual Download Page 13

Page: 13 / 62

Introduction & Specifications

Port Statistics

200R204-000

Innovx FastSwitch Ethernet Switch

1-5

Issue 2

Installation and Operation Manual

Port Statistics

Innovx FastSwitch accumulates statistics for each port. Displayed at the command line interface,
these statistics help in troubleshooting network problems and measuring network performance.

Table 1-1

Available Port Statistics

Statistics

Description

RX Octets

Counts total bytes received by a port.

RX Dropped Packets

Counts good packets that had to be dropped after receipt.

RX Broadcast Packets

Counts good packets destined for a broadcast address.

RX Multicast packets

Counts good packets destined for a multicast address.

RX Unicast Packets

Counts good packets destined for a unicast address.

RX Undersize Packet

Counts good packets less than 64 bytes long.

RX Pause Packet

Counts valid Pause frames.

RX 64 Octet Packets

Counts packets that are 64 bytes long.

RX 65-127 Octet Packets

Counts packets between 65 and 127 bytes long.

RX 128-255 Octet Packets

Counts packets between 128 and 255 bytes long.

RX 256-511 Octet Packets

Counts packets between 256 and 511 bytes long.

RX 512-1023 Octet Packets

Counts packets between 512 and 1023 bytes long.

RX 1024-1522 Octet Packets

Counts packets between 1024 and 1522 bytes long.

RX Oversize Packets

Counts good packets that are greater than 1522 bytes long.

RX Jabbers

Counts errored packets that are greater than 1522 bytes long.

RX Alignment Errors

Counts errored packets between 64 and 1522 non-integer number of bytes.

RX FCS Errors

Counts packets with a bad Frame Check Sequence.

RX Good Octets

Counts total good packets received.

RX Fragments

Counts errored packets less than 64 bytes long.

RX SA Changes

Counts the times the source address has changed from the previous value.
Indicates the port is connected to a repeater-based network.

RX Excess Size Disc

Counts good packets discarded due to length exceeding 1536 bytes.

RX Symbol Error

Counts valid length packets that have at least one invalid data symbol.

TX Octets

Counts good bytes of data transmitted.

TX Dropped Packets

Counts packets that had to be dropped before and after transmission.

TX Broadcast Packets

Counts good packets destined for a broadcast address.

TX Multicast packets

Counts good packets destined for a multicast address.

TX Unicast Packets

Counts good packets destined for a unicast address.

TX Collisions

Counts collisions during packet transmission.

TX Single Collisions

Counts packets transmitted successfully after one collision.

TX Multiple Collisions

Counts packets transmitted successfully after more than one collision.

TX Deferred Transmit

Counts packets transmitted after first attempt was delayed due to busy medium.

TX Late Collisions

Counts times that a collision is detected later than 512-bit times into packet.

TX Excessive Collisions

Counts packets that are not transmitted after 16 failed attempts.

TX Frame in Disc

Counts valid packets received that cannot be forwarded due to congestion.

TX Pause Packets

Counts Pause frames transmitted.

Summary of Contents for FastSwitch































































Search results

Summary of Contents for FastSwitch

Reviews:

Related manuals for FastSwitch

Brands by name

Popular brands

Innovx FastSwitch, Installation & Operation Manual

Search results

Summary of Contents for FastSwitch

Reviews:

Related manuals for FastSwitch

Brands by name

Popular brands