innovair Inverter FLEX24 DEV24H2R18 Service Manual Download

Page: 49 / 121

SERVICE MANUAL

Troubleshooting

：

Driver module sensor error

Replace the drive board

3.4.19 “P8” Driver Module High Temperature Protection

Error display:

ODU mainboard LED displayer

Error judgment condition and method:

If IPM module temperature or PFC module temperature exceeds the set protection value, then it can be

judged that driver module temperature is too high and system will shut down for protection.

Possible reason:

Thermal grease is not applied or not evenly applied to the module, or there is other substance on the back of the

module.

The module securing screws are not tightened up.

Drive board temperature sampling circuit element is damaged or drive chip temperature sampling AD terminal is

abnormal.

Troubleshooting

：

Summary of Contents for Inverter FLEX24 DEV24H2R18


























































































































Search results

Summary of Contents for Inverter FLEX24 DEV24H2R18

Reviews:

Related manuals for Inverter FLEX24 DEV24H2R18

Brands by name

Popular brands

innovair Inverter FLEX24 DEV24H2R18, Service Manual

Search results

Summary of Contents for Inverter FLEX24 DEV24H2R18

Reviews:

Related manuals for Inverter FLEX24 DEV24H2R18

Brands by name

Popular brands