InfiRay Tube Series Operating Manual Download Page 29

Page: 29 / 37

InfiRay Outdoor

•

Tube TH35/TH50

•

Operating Manual www.infirayoutdoor.com

Image Mode:

White hot

Zeroing Distance:

A100

Ultraclear Mode

: Off

Optical Magnification:

3.5×(TH35:2.5×)

Calibration Mode

: A

Compass:

Off

Standby:

Off

Video Output:

Off

Wi-Fi:

Off

Gravity Sensor:

Off

Unit of Measure:

Meter

Status Auto Hiding:

Off

Info

Show the device information

⚫

In the

Settings

submenu, rotate the rotary encoder

(7)

to select

the

Factory Reset

option.

⚫

The relevant information of riflescope will be shown by a short press

of the rotary encoder

(7).

⚫

This item allows the user to view the following information about the

riflescope: the product model, GUI version, SYS Info, Boot version,

FPGA, PN and SN number of the riflescope, Hardware version and

FCC ID.

⚫

Press and hold the rotary encoder

(7)

to return to the upper menu

interface.

Summary of Contents for Tube Series





































Search results

Summary of Contents for Tube Series

Reviews:

Related manuals for Tube Series

Brands by name

Popular brands

InfiRay Tube Series, Operating Manual

Search results

Summary of Contents for Tube Series

Reviews:

Related manuals for Tube Series

Brands by name

Popular brands