Inficon UL5000 Technical Handbook Download Page 94

Page: 94 / 108

Maintenance works

iina

e 0

chn

ica

l ha

boo

9.5.4

16000 hours maintenance

The 8000 hours maintenance should be performed by an INFICON service tech-
nician or an other authorized person.

After 16000 working hours the bearing of the turbo pump and the different kind of fore
pump will reach their expecting life time.

The scroll module (IWATA ISP 500 or Varian TS 620) and the turbo pump must be
replaced.

The maintenance work will take approximately 10.0 hours.

Work to be performed

Required materials

P/N

Exchange the scroll module (IWATA ISP-
500B)

•

Scroll module for IWATA ISP-500B

200000217R

Exchange the scroll module (Varian TS
620)

•

Scroll module for Varian TS 620

200001665R

Replace TMH 071

•

Turbo pump TMH 071

200000569R

Take apart the valve bloc and clean it

Replace the seals for valves

•

Set of seals for valve bloc

•

Set of seals for valves

200000593

200000594

Check and/or replace Filters

•

Spare Filter Cell for the fans

•

Spare Filter for venting and purge line

•

Silencer for exhaust (only UL1000 Fab)

200000685

200000683

20099183

Functional check and adjustement

Summary of Contents for UL5000













































































































Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands

Inficon UL5000, Technical Handbook

Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands