Inficon UL5000 Technical Handbook Download Page 47

Page: 47 / 108

Description of the Menu

iina

e 0

chn

ica

l ha

boo

6.2

View

•

Main Menu

View

In this menu

Fig. 6-3

all features that influence the way data are displayed are put

together.

6.2.1

Scale linear/logarithmic

•

Main Menu

View

Scale linear/logarithmic

These settings apply to the bargraph (= bar underneath the digital figures in the
measurement mode) and Y-axis in the trend mode.

The scale of the bargraph can either be linear or logarithmic. With the arrows (up and
down) it can be determined how many decades the bargraph covers.

Usually a logarithmic scale is recommended because leak rates may change easily
over several decades.

Fig. 6-3: The

View

Key No.

Name

Description

Back

Return to the main menu.

Scale linear/logarithmic

Settings for bargraph and trend mode.

Please refer to Chapter

6.2.1

Display-range auto/manual

Manual or automatic scaling. Please refer to
Chapter

6.2.2

Time axis

Time axis in trend. Please refer to Chapter

6.2.3

Contrast

Display contrast. Please refer to Chapter

6.2.4

Background in Stand-by

Background displayed or not. Please refer to
Chapter

6.2.5

Decimal places

Number of decimal places. Please refer to
Chapter

6.2.6

Lower display limit

Please refer to Chapter

6.2.7

Softkey 2:

Linear

Pressing this key switches the display to a linear scale, starting at zero.

Softkey 6:

Log

The scaling will be displayed logarithmically.

Summary of Contents for UL5000













































































































Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands

Inficon UL5000, Technical Handbook

Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands