Inficon UL5000 Technical Handbook Download Page 60

Page: 60 / 108

Description of the Menu

iina

e 0

chn

ica

l ha

boo

6.6.1.4

HYDRO•S

Notice:

This setting is only valid, if mass mode is set to „

He“. See Chapter

6.3

You can always switch HYDRO•S on and off manually, even if automatic is enabled.

Notice:

Switching HYDRO•S manually, deactivates the automatic until the next
measuring cycle (STOP/START).

6.6.1.5

Leak rate internal test leak

•

Main Menu

Settings

Vacuum settings

Leak rate internal test leak

The value of the internal test leak can be set. See Chapter

4.2.2.7

Numerical Entries

for the description of the entry.

Softkey 7:

enable

If HYDRO•S automatic is enabled, the UL5000 switches HYDRO•S on and
off at the following conditions:

HYDRO•S is switched on, if

•

ZERO is off and

•

p1<0,3mbar and

•

Leak rate is between 2×10

-10

mbar l/s and 3×10

-10

mbar l/s and

•

HYDRO•S was not switched on manually

The lower detecting limit for HYDRO•S is 1×10

-10

mbar l/s

Softkey 3:

disable

HYDRO•S is disabled. Leak rate higher than 3×10

-10

mbar l/s

If HYDRO•S is disabled, it can not be switched on/off manually anytime.

Softkey 5:

Automatic OFF

HYDRO•S can be switched on/off manually by Softkey 4 in display mode
(See Chapter

5.4.6

)

Warning

Normally there is no reason to edit the leak rate of the internal test leak besides after
a change of the internal test leak. A wrong leak rate of the internal test leak will lead
to wrong leak rate readings!

Summary of Contents for UL5000













































































































Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands

Inficon UL5000, Technical Handbook

Search results

Summary of Contents for UL5000

Reviews:

Related manuals for UL5000

Brands by name

Popular brands