IndigoVision 9000 Series User Manual Download Page 22

Page: 22 / 68

User Guide - v7

Fixed
Dome

CAT5 crossover

cable

Power supply

Figure 14:

Connecting the device and PC using a cross-over cable

Alternatively, you can connect the unit and PC to the same PoE switch.

Fixed

Dome

CAT5 cable

PoE switch

Figure 15:

Connecting the unit using a PoE switch

A further alternative is to connect the unit to the PC via a PoE injector.

OUT

PoE injector / midspan

Mains Power

Supply

Cat5 crossover

cable

Cat5 cable

Fixed
Dome

Figure 16:

Connecting the unit using a PoE injector

Preparing for initial device configuration

You cannot connect the device to your network until you have changed the IP settings to suit
your network.

To change the factory defaults of your device, you must first, temporarily, modify your PC’s
network settings.

Make a note of the original value of all settings that are to be changed so that you can re-enter
them when you have completed the initial device configuration.

3 Getting Started

Enhanced SD Fixed Dome - 9000 Range

Summary of Contents for 9000 Series





































































Search results

Summary of Contents for 9000 Series

Reviews:

Related manuals for 9000 Series

Brands by name

Popular brands

IndigoVision 9000 Series, User Manual

Search results

Summary of Contents for 9000 Series

Reviews:

Related manuals for 9000 Series

Brands by name

Popular brands