IEI Technology IMB-H810-i2 User Manual Download Page 69

Page: 69 / 215

IMB-H810-i2 microATX Motherboard

Page 53

4.2.1 Socket LGA1150 CPU Installation

WARNING:

CPUs are expensive and sensitive components. When installing the

CPU please be careful not to damage it in anyway. Make sure the CPU

is installed properly and ensure the correct cooling kit is properly

installed.

DO NOT touch the pins at the bottom of the CPU. When handling the

CPU, only hold it on the sides.

To install the CPU, follow the steps below.

Step 1:

Disengage the load lever

by pressing the lever down and slightly outward to

clear the retention tab. Fully open the lever. See

Figure 4-1

Figure 4-1: Disengage the CPU Socket Load Lever

Step 2:

Open the socket and remove the protective cover.

The black protective

cover can be removed by pulling up on the tab labeled "Remove". See

Figure 4-2

Summary of Contents for IMB-H810-i2
























































































































































































































Search results

Summary of Contents for IMB-H810-i2

Reviews:

Related manuals for IMB-H810-i2

Brands by name

Popular brands

IEI Technology IMB-H810-i2, User Manual

Search results

Summary of Contents for IMB-H810-i2

Reviews:

Related manuals for IMB-H810-i2

Brands by name

Popular brands