IEI Technology IMB-H110 User Manual Download Page 58

Page: 58 / 161

IMB-H110 microATX Motherboard

Page 43

3.2.26 RS-232/422/485 Serial Port Connectors

CN Label:

COM5, COM6

CN Type:

10-pin header, p=2.00 mm

CN Location:

See

Figure 3-27

CN Pinouts:

See

Table 3-22

Each of these connectors provides RS-232/422/485 connections.

NOTE:

The communication protocol of the serial ports is set through the BIOS menu

in “Advanced

Super IO Configuration

Serial Port 5/6 Configuration”. Use

the

Transfer Mode

BIOS option to configure the correspondent serial ports

(refer to

Sections 5.3.3.4.2

and

5.3.3.4.3

for detailed information).

Figure 3-27: RS-232/422/485 Serial Port Connector Locations

Pin

Description

Pin

Description

DCD/TX-/D-

DSR

RX/TX+/D+

RTS

TX/RT+

CTS

Summary of Contents for IMB-H110


































































































































































Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands

IEI Technology IMB-H110, User Manual

Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands