IEI Technology IMB-H110 User Manual Download Page 139

Page: 139 / 161

IMB-H110 microATX Motherboard

Page 124

Quiet Boot [Enabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.

Disabled

Normal POST messages displayed

Enabled D

EFAULT

OEM Logo displayed instead of POST messages

Launch PXE OpROM [Disabled]

Use the

Launch PXE OpROM

option to enable or disable boot option for legacy network

devices.

Disabled D

EFAULT

Ignore all PXE Option ROMs

Enabled

Load PXE Option ROMs.

Option ROM Messages [Force BIOS]

Use the

Option ROM Messages

option to set the Option ROM display mode.

Force

BIOS

EFAULT

Sets display mode to force BIOS.

Keep

Current

Sets display mode to current.

UEFI Boot [Disabled]

Use the

UEFI Boot

option to enable or disable to boot from the UEFI devices.

Enabled

Boot from UEFI devices is enabled.

Disabled D

EFAULT

Boot from UEFI devices is disabled.

Summary of Contents for IMB-H110


































































































































































Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands

IEI Technology IMB-H110, User Manual

Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands