IEI Technology IMB-H110 User Manual Download Page 115

Page: 115 / 161

IMB-H110 microATX Motherboard

Page 100

Auto mode fan start/off temperature

Use the + or – key to change the

Auto mode fan start/off temperature

value. Enter a

decimal number between 1 and 100.

Auto mode fan start PWM

Use the + or – key to change the

Auto mode fan start PWM

value. Enter a decimal

number between 1 and 100.

Auto mode fan slope PWM

Use the + or – key to change the

Auto mode fan slope PWM

value. Enter a decimal

number between 1 and 64.

5.3.6 RTC Wake Settings

The

RTC Wake Settings

menu (

BIOS Menu 12

) enables the system to wake at the

specified time.

Advanced

Wake system with Fixed Time

[Disabled]

Enable or disable System
wake on alarm event. When
enabled, System will
wake on the
date::hr::min::sec
specified
----------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 12: RTC Wake Settings

Summary of Contents for IMB-H110


































































































































































Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands

IEI Technology IMB-H110, User Manual

Search results

Summary of Contents for IMB-H110

Reviews:

Related manuals for IMB-H110

Brands by name

Popular brands